商品規格 |
如果您有一台帶有 HDMI 輸出的電腦或平板電腦或設備,但您想將其連接到投影機、顯示器或帶有 VGA 輸入的顯示器,那麼您來對地方了! 這種漂亮的結合器電纜一端有一個經典的 HDMI 插頭連接器,另一端有一個 DB-15 VGA 連接器(它有六角螺母,如果您試圖將它與也有六角螺母的電纜配對,則可以將其拆下)。 側面還有一個音訊插孔,可提供立體聲耳機/線路輸出(HDMI 1.3 電纜同時傳輸影片和音訊)。 您可能還需要一根 VGA DB15 公/公電纜(未隨附但可在商店購買)將其連接到您的顯示器。
我們使用 Raspberry Pi 和我們擁有的舊 VGA 顯示器進行了嘗試,發現顯示輸出非常清晰生動。 該影片與開箱即用的 Raspberry Pi 配合使用效果極佳。 要啟用音訊並自定義解析度,請檢查我們建議的 /boot/config.txt 的技術選項卡最簡單的方法是將編程的 Pi SD 卡插入您的電腦並查找 config.txt 文件 SD卡根目錄,編輯並保存。 如果您可以將 HDMI 輸出設置為匹配的解析度,顯示器將看起來最好,所以如果您想要一個漂亮的顯示,請嘗試這樣做。
它也適用於其他類型的電腦和 HDMI 輸出設備,我們將其插入 XBOX360 和 Windows 盒子,它作為顯示面板中具有可調解析度(從 800x600 到 1920x1080)的輔助顯示器出現。
Package comes with one HDMI to VGA adapter.這是我們已知的 /boot/config.txt,它將解析度設置為 800x600 並啟用記憶卡的音訊。 我們還記錄了其他幾個解析度選項!
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=87
# Put your VGA monitor resolution below
# hdmi_cvt =
# width width in pixels
# height height in pixels
# framerate framerate in Hz
# aspect aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4, 5=16:10, 6=15:9
# margins 0=margins disabled, 1=margins enabled
# interlace 0=progressive, 1=interlaced
# rb 0=normal, 1=reduced blanking
# For example, 800x600 @ 60 Hz
hdmi_cvt=800 600 60 1 0 0 1
# or maybe 800x480 @ 60 Hz
#hdmi_cvt=800 480 60 6 0 0 1
# or, 1024 x 768 @ 50 Hz
#hdmi_cvt=1024 768 60 1 0 0 1
# or if you're not sure, nothing beats 640x480
#hdmi_cvt=640 460 60 1 0 0 1
# see http://www.raspberrypi.org/forum/viewtopic.php?f=29&t=24679
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
###############################################################
### THIS LINE IS WHAT ENABLES THE AUDIO OUT OF THE ADAPTER! ###
hdmi_drive=2
###############################################################
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# for more options see http://elinux.org/RPi_config.txt
出貨清單 |